| Category: |
Paper Crafts Suppliers
|
| Title: |
The Craft Cabin
|
| Listing URL: |
http://www.the-craft-cabin.co.uk
|
| Description: |
Our family-run craft business specializes in card making, scrapbooking, DIY wedding stationery crafts, paper crafting & card craft supplies. Be sure to sign up for our free newsletter with competitions, card making ideas, wedding templates, scrapbook projects, workshops, classes & free demo’s.
|
| Crafty Tips: |
Editor's Note: A special thank you to the Craft Cabin for writing not only a tip, but this wonderful article on using Shrink Plastic!
Using Shrink Plastic
Types of shrink plastic:
There are various products from different companies including unsanded, sanded, in black, white, frosted and clear & now even pre-printed & wallpaper. The plastic shrinks to approx 45% of the original size.
Black - shrinks the fastest and the 'gooiest'; white - good for clear, sharp colours and using with pencils; frosted - one side ready roughened with a clear back for 'window' designs, and totally clear for a variety of effects.
If not bought ready sanded you will need to sand the plastic first using 320 - 400 grade wet and dry paper for best results and sanding both ways and both sides if you wish to colour the back as well. Sanding the back also helps to avoid sticking when heating. Do not sand clear plastic or it will have a frosted instead of clear appearance.
Colouring:
The most important thing to remember is that the colour intensifies after shrinking so 'less is more', go easy or your results will be very dark. A few trial runs and a little practice you will find the right balance.
Think shrink, think non-porous?
Inkpads
There are few 'definites' with shrink plastic, each make and type can behave differently. However there are a few inks that will always work well, and others that rarely do.
When stamping directly onto the plastic there are two surfaces to consider - the un-sanded, shiny and slippery side and the other sanded or frosted (ready roughened) side.
Some pigment and dye ink will not dry on un-sanded shrink, even with heat, and many dye inks bleed on sanded shrink.
You will see that there are sometimes reasons for not sanding although a steady hand is needed on the slippery surface.
Some Inks will give clear dry images on both sanded and un-sanded surfaces.
Heat Set and permanent pigment inks 'hold' on the slippery surface - Versacolor & Stazon.
Use inkpads for sanded surfaces and various pigment inks, Ranger Archival, Fluid Chalk ink
TIPS:
Dry ink a little before shrinking to avoid smudging when curling, hold the heat gun very high above the stamped plastic - hand hot- for 15 seconds before lowering to shrink. This is one of the times when a hair dryer is useful as you don't worry about too much heat.
So you don't want an uncoloured background - no problem, let's colour the plastic first and then over stamp. Thee are extra possibilities now as more inks will bond over a background layer.
Inks for background colour. Brilliance, Colourbox Fluid Chalks and chalk palettes are always reliable for background colouring. Apply direct from the pad onto plain or sanded surfaces, not too much and blend colours before using the high -heat method to dry and set ink. Brilliance pearlescent 'ice blue' is especially impressive and rainbow pads work well, but do not apply too thickly.
When dry, over stamp with a range of other pigment and dye ink - Adirondack & Versamark/Versacolour pigments; and too many others to mention. Try for yourself as many will give a clear sharp image. Stazon might blur but is better on some surfaces than others.
Other Ideal Colouring Mediums.
Sakura Stardust Pens, Permanent Markers, Colouring Pencils, Waterproof inks, Fabric Paint, and Chalks
Colouring in Images:
Colouring pencils, both watercolour and plain blendable are the ideal medium for shrink plastic; easy to use, an endless range of colours and perfect, clear and bright results. Remember, a light touch, don't be too heavy handed with the colour as colour intensifies when shrunk. Use on a sanded surface.
Cutting, Shrinking & Glueing:
Pieces can be cut before or after colouring. The edges become sharper after shrinking, so round the corners a little and/or trim to the eventual shape that you require. It is possible to trim after shrinking with sturdy kitchen type shears and a shot of heat will soften the plastic.
Punching a hole before shrinking saves drilling afterwards. Remember the hole will also shrink. Edges can be cut with decorative scissors.
The first time you shrink can be quite alarming if you do not know what to expect. The plastic curls and twists alarmingly before finally flattening - you can hold it down with a wooden stick, brush handle, chopstick or tweezers. Just touching the stick on the surface is enough to stop it blowing away.
Move the heat gun with a circular motion for an even heat and slower heating can help keep difficult shapes from getting out of control. There are differing views on gentle/fast heat; you find your own preference with practice.
Clear plastic might stick to itself so gently prise apart before cooling and reheat a little if necessary. Small, delicate shapes might need some extra attention to straighten. When ready use a piece of thick card, wood or the back of an Acrylic mount to flatten. If you have a raised surface from bubbled paint etc. do not press, the piece will lie reasonably flat without pressing. The warm plastic can be bent and twisted into shapes if preferred.
For large pieces - or multiple pieces for necklaces etc. shrink in an oven. A toaster oven is recommended, but not necessary as Shrink plastic is a non-toxic material even when heated. A regular oven, 225%F or 110%C for five minutes + without pre-heating will help prevent curling, but higher heat is often also recommended - experiment again. Use a Teflon baking sheet and when cold the pieces will easily lift off. The sheet is also useful when shrinking with a heat gun. Use over a stack of paper or board to protect worktop. An off-cut of laminated board from a DIY store is very inexpensive and useful when painting as well as when shrinking.
Gluing is another tricky subject affected by the type of plastic and colouring on the surface. Thin slices of glue gun glue stick melted with a heat gun will join pieces together and strongly adhere onto card and other surfaces. Apply direct to plastic, hold with a kebab stick and blast until melted or melt a little on foil or heat mat and transfer with a cocktail stick to the plastic and join to other surface. Beads and glitter can be added before drying. Try Anita's Tacky Glue or special bead craft glue for attaching beads. Sand surfaces to be joined with an emery board and peg or clamp together for better adhesion.
Stamping into the hot plastic after shrinking. Remember to start with a piece more than twice as wide and long as the finished stamped image. Colour before shrinking, and add embossing powder for a special colourful effect before shrinking. Leave the stamp until cold and it will lift off easily. The stamp can be inked for colour or the piece coloured when cold with paint, chalk, ink or Metallic Rub-ons
Make Your Own Sample Chart
Shrink Art is the one technique that really benefits from a few samples. Be sure to try all of the different types of coloured shrink plastic. Frosted shrink is easy and useful for beginners; clear on one side with a rough finish on the other.
Cut a sheet into 20 x 5cm squares. Choose one or two stamps with clear lines and open spaces to colour. Flower heads, cutie animals or brushstroke images etc.
Try stamping first with some of the suggested inks on clear and rough sides. Shrink and see the results. Try colouring in the images as suggested and shrink.
Now try some background ideas, over stamp or add embossing powders, glitter etc and shrink.
Try a couple of painted samples. See how the images stamped on the rough side can been also seen from the back - two images for one. Try thicker paint and shrink for a bubble effect.
Add embossing powder with Versamark before shrinking for magical colouring and texture.
Keep samples and attach with sticky dots to a piece of card and label as a reminder of best inks etc.
Now you are ready to create your own fantastic art. Please share new ideas and discoveries with other stampers when ever possible.
Some Ideas For Using Your Finished Projects:
Shrink plastic charms can be used in so many ways! Besides making cute embellishments on your card making projects & scrapbook pages, use shrink plastic to make theme charms for every occasion.
1. Use rubber stamps to create and color your with sakura glitter pens.
2. Tie or glue onto barrettes for cute hair clips
3. Add jump rings and use as zipper pulls on coin purses, backpacks, jacket, or day planner
4. Make shoelace charms to teach kids which shoe goes on the right and left foot
5. Keyrings
6.Clear Shirk Plastic makes lovely sun catchers and wind catchers
7.Tie to gift packages along with the tag, or make the tag itself
8. Use Christmas punches to make your own tree ornaments
9. Buttons: can't find the button color that you want? Want a super tiny button to use on your title or journaling squares?
10. Simply use any size circle punch (or cutter), color the plastic using any pigment or permanent ink, punch holes in the center and shrink. Instant custom buttons. Very economical--1 8x10 sheet will make up to 100 buttons!
11. Tags: Using a die cut or a bought tag or template, trace the shape onto the shrink plastic. Decorate using pigment or permanent inks or pens, stamps, and punches. Cut out the tag, punch the hole at the top (if desired) and shrink. The result is a tiny tag that looks good strung on a border or on titles or just as simple accents.
12.You can print photos onto shrink plastic, then shrink them down for a very cool embellishment! Choose the "draft" printing option, it uses less ink and will produce better results. Choose the A4 size shrink plastic.
Use your imagination and have fun with this fun technique...Happy Shrinking
|
| Clicks: |
11
|
| Link added: |
Jun 19, 2007
|
|
